Is the RainControl only for use with rainwater?

Simply, no. The RainControl can be used with other fluids. As long as the pressure sensor being used is tolerant of the fluid (viscosity, temperature, pH etc.) the RainControl can be used.

Do I need to build a panel around the RainControl?

Not at all. The RainControl functions as a level controller on its own. However, you can use the output from the RainControl to operate other components of a larger controller.

I’m trying to maintain a minimum tank level, from either mains water or a holding tank. Is the RainControl suitable for this?

Absolutely! The RainControl is totally suitable for maintaining a minimum tank level from either mains water or a holding tank. It can activate/deactivate a pump, solenoid, or simple mechanical valve using its onboard relay. The only thing you need to do is define the activation range, which includes the levels for activation and deactivation.

I need to set a high-level alarm on a holding or process tank. Should I consider using the RainControl, or do I need to create something from scratch?

This is a slightly trickier scenario. Yes, the RainControl can be used as a high-level system by triggering a beacon or sounder, depending on the location and ambient noise. However, if you need to activate a local beacon, or a remote beacon, and open a spillway or overflow solenoid, this would require a more complex controller. You would need to use the output from the RainControl to drive either a secondary controller or relays for this purpose.

I want to keep a tank at a minimum level, as in I want to hold water in a tank and release it over time, along the lines of a retention tank. Would the RainControl work in this situation?

I particularly liked this question. The answer is yes! With a little planning, a throttled outlet with a motorised valve can be activated by the RainControl. It really is only a matter of calculating the required flow rate and minimum tank level. Of course, if we wanted to get a little clever, the designer could add other functions like a high-level alarm or discharge notification by using the RainControl output to drive multiple relays. A setup like this can be as simple or complicated as the designer (or user) wants, and all centralised around a simple little box.

I have another potential use for the RainControl Tank Level Controller who can I contact for more information?

As always, with any of the Mac3 products, we are always happy to discuss them in greater detail and how they can be deployed in your designs or installations. Contact Jim, our Mac3 Technical lead. Jim and Tom have over 25 years of experience in Water Control Systems.

The post FAQs RainControl – Tank Level Controller appeared first on Mac 3 UK.

RainControl rom Mac3 – Tank-level Control

Any Rainwater Tank level control system consists of four elements:

• A tank
• Rainwater harvesting
• Mains-water
• Controller

The key objective is to maximize the storage and use of harvested rainwater while minimizing the use of mains water. This requires a delicate balance as we experience fluctuating periods of wet weather and droughts with little warning. During wet periods the water tanks are full, but in the increasingly common dry summers, the tanks run low. Depending on usage, this can lead to various problems, from sanitation issues (such as yard washdown and toilet flushing) to maintenance issues (such as pump damage due to running dry). Not to mention the alarmed calls from sites/users when things don’t run exactly as expected. this is the point where an end user will ask ‘What’s the point of this system if it doesn’t work without rain?’ followed shortly by ‘To hell with it, I’ll just use the mains instead’.

RainControl for tank level control

At this point, we can pull a RainControl from our sleeve, either in the design stage or retrofitting to a pre-existing tank installation to add both level monitoring and top-up functionality.

The RainControl is designed to be DIN-rail mounted, allowing for installation in both panel mount systems or as a standalone unit in a windowed project box. The RainControl panel displays the live level inside the tank along with top-up status. It uses a pressure transducer, which eliminates the need for moving parts inside the tank, simplifying installation and use as only one input has to be configured.

Overview of the settings on the Mac3 RainContro

Now, unlike the majority of ‘simple’ or ‘basic’ top-up systems, the RainControl doesn’t add water to the tank for a specific amount of time, rather the RainControl can be configured to add a measured amount of water. This allows the installer (or end user) to set or adjust the minimum and maximum intervention levels inside the tank. When properly configured, this ensures that there is always a minimum level of water in the tank. When the RainControl detects that the water level has dropped below the minimum set level, it opens a solenoid or motorized valve to top up the tank until it reaches a specified maximum level. Once the tank is filled to this level, the RainControl closes the valve or solenoid until the water level drops again to the initial minimum point.

RainControl for Tank Emptying

We could use the same simple system to drain a tank. Turning this on its head, rather than filling a water tank, the relay inside the RainControl could be connected to a pump rather than a valve. So using the same setup (and just a touch of cunning) we can set the operational levels for draining a tank once it reaches level ‘x’ turning off the pump at level ‘y’.

This is an interesting idea for SuDS systems if we use an attenuated outflow on a motorised valve rather than a pump. The RainControl is a robust reliable system at a very competitive price point.

RainControl for Tank Level Alarm

The use of pumps/valves (and solenoids) is certainly one avenue. The RainControl could also easily be adapted into a high/low-level alarm using the relay to activate an alarm rather than a pump or valve. Again, it’s robust, simple to configure and install and competitively priced.

RainControl from Mac3

As with much of the Mac3 line, there are multiple uses for any given piece of equipment given a little design thought. The RainControl is a flexible addition for any parts list if building a controller from scratch, adapting an existing installation to a new purpose (always good fun) or simply replacing a failed system, there will always be a use for the RainControl.

Why not contact us if you have a thought about how you could use one of these anew, or to repair a failed system. We particularly love fixing redundant Rainwater Harvesting systems and bringing Rainwater Harvesting tanks back into use.

For more information

Contact Jim, our Mac3 Technical lead. Jim and Tom have over 25 years of experience in Water Control Systems.

The post RainControl – Tank Level Control appeared first on Mac 3 UK.

The MacNivel is possibly the simplest method of displaying the liquid level in a tank level I’ve encountered. Unfortunately, this makes writing about it somewhat challenging!

Liquid Level Indicator – MacNivel from Mac3

If I remember one thing from my secondary school days, it would be my first teacher drilling K.I.S.S (Keep It Simple Students – well, maybe not students) into a class of kids. But he was certainly onto something because who doesn’t like a simple life?

Traditionally, installing any liquid level monitoring is something that must be done during tank installation. It often requires installing level sensors (reed switches, probes or float switches) into the tank (that can require modification of the tank itself), adding ducting for running cables and power requirements for the level monitor.

MacNivel with 5-core sensor cable

The MacNivel, however, only requires a single multi-cored cable to be put into the tank. Yes, it is really that simple! Setting the levels is as easy as cutting (and stripping) the individual cores to the depths you want to measure against.

This one, (pictured right), uses a 5-core sensor cable – which I’d typically suggest for installations. As a stranded cable, it will be easier to manipulate around obstructions.

MacNivel fitted with network cable (5 core cable)

I’ve tried a few different cable types. Even using a network cable (someone in the office laughed at me – being a technical geek I proved them wrong! (see picture to left).

So long as there are five individual cores – 1 is the common, which is the lowest inside the tank – the remaining 4 are the displayed levels on the MacNivel display.

So long as the liquid is conductive, the MacNivel can give a reading.

Retrofit liquid level indicator

Using a small diameter cable, retrofitting to pre-existing installations is much simpler. For example, when adding a liquid level indicator to a water tank in a caravan or a water bowser on a trailer, route the cable, suitably mount the MacNivel (not forgetting to add a 9v battery), and then take a tea break. It’s truly that simple!

Of course, using a battery is a benefit all its own. There is no need to mess about with power cables or power supplies (I think everyone has had the ‘fun’ of trying to find a suitable power supply) or running extra cables. Not to mention if your project is off-grid (or mobile) there will always be a battery (or three) – in a drawer somewhere.

MacNivel – perfectly suited to permanent or temporary installations, where other monitors just won’t fit.

For more information

Contact Jim, our Mac3 Technical lead. Jim and Tom have over 25 years of experience in Water Control Systems.

The post MacNivel – Liquid Level Indicator appeared first on Mac 3 UK.